Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
Almost everyone has their own individual theory with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a brand-new one is also a reasonably tough project. If the old tub is easily available, the project can move quickly; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the task is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to move out the old bathtub as well as set in the new one. Make sure you have certified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require a specialist plumber to make tube links.
This write-up will aid you install a new tub in your bathroom if you have currently purchased a brand-new bathtub as well as do not need to transform the plan of your previous water system pipelines.
Your tools as well as material list ought to consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the supply of water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be quite bothersome because of the limited gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind needs to be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Utilizing both wood boards under its feet, position the tub in the required placement. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bath tub up until the level reads degree.
To install faucets, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
Turn on the water system and also inspect all joints as well as brand-new pipework for leakages and tighten them if needed. Fill up the bathtub as well as likewise examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and securing around the tub ought to wait till the tub has actually been utilized at the very least once as this will settle it into its last position.
Preparing for the Setup
Firstly, the supporting framework provided with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break a rigid seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water before securing, to permit the motion experienced when the tub remains in use. The sealant can crack fairly early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that editorial about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on another web page. Do you know another person who is involved in the topic? Feel free to promote it. I am grateful for your time. Don't forget to check up our blog back soon.
Address all plumbing emergencies here. Report this page